Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
On the reversion and recrystallization of austenite in the interstitially alloyed Ni-free nano/ultrafine grained austenitic stainless steels
Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran.
Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran.
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0002-7527-719X
Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran.
2019 (engelsk)Inngår i: Metals and Materials International, ISSN 1598-9623, E-ISSN 2005-4149, Vol. 25, nr 4, s. 846-859Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The martensite reversion treatment was conducted on two grades of Ni-free austenitic stainless steels interstitially alloyed with C and N. The hot rolled sheets of steels were cold rolled up to 80% thickness reduction to acquire strain-induced α′-martensite and subsequently reversion annealed at temperatures from 700 to 850 °C for 1 to 1000 s to revert the α′-martensite to austenite. Microstructural evolution was investigated using optical microscopy, X-ray diffraction, electron backscatter diffraction, and magnetic measurement techniques. Mechanical properties were measured using tensile tests at room temperature. The resultant microstructures contained both reverted and recrystallized austenite when reverted at 700 and 750 °C with the annealing time less than 100 s. A nonuniform grain structure was characterized under these conditions consisting of nano/ultrafine grains formed via α′-martensite reversion and coarser grains by recrystallization of the retained austenite. However, a more uniform austenite grain size with average size of 1 μm was obtained at 850 °C for 1000 s. The specimens having nonuniform grain structure exhibited excellent combinations of strength and ductility. A variety of mechanical properties was achieved depending on the annealing condition. The work hardening behavior affected UTS and ductility of the studied steels. The shift of the work hardening peaks to the higher strains was found suitable for ductility. Addition of C to N-containing Ni-free steels deteriorated mechanical properties. Best combination of strength and elongation was obtained in the test material with lower C/N ratio. 

sted, utgiver, år, opplag, sider
Springer, 2019. Vol. 25, nr 4, s. 846-859
Emneord [en]
Interstitially alloyed austenitic stainless steel, Mechanical properties, Nano/ultrafine grain size, Ni-free stainless steel, Recrystallization, Reversion annealing
HSV kategori
Identifikatorer
URN: urn:nbn:se:hj:diva-45489DOI: 10.1007/s12540-019-00255-wISI: 000473163200003Scopus ID: 2-s2.0-85061302943OAI: oai:DiVA.org:hj-45489DiVA, id: diva2:1341204
Tilgjengelig fra: 2019-08-08 Laget: 2019-08-08 Sist oppdatert: 2019-08-08bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Ghassemali, Ehsan

Søk i DiVA

Av forfatter/redaktør
Ghassemali, Ehsan
Av organisasjonen
I samme tidsskrift
Metals and Materials International

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 43 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf