Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Prototyping of a high pressure die cast al-si alloy using plaster mold casting to replicate corresponding mechanical properties
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0001-5753-4052
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0002-7527-719X
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0002-0458-3456
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0001-6481-5530
2019 (engelsk)Inngår i: Minerals, Metals and Materials Series, Springer, 2019, s. 435-442Konferansepaper, Publicerat paper (Fagfellevurdert)
Abstract [en]

Prototyping prior high pressure die casting (HPDC) is used for product/mold design optimization. Plaster mold casting is a cost-efficient prototyping technique providing good surface quality and dimension accuracy, similar to HPDC components. However, the corresponding mechanical properties of a component produced with these two methods are diverging significantly, mainly due to differences in the cooling rate. This work presents a procedure to optimize the plaster mold casting for prototyping to replicate mechanical properties of a commonly used Al-Si alloy (A380). Two commercial alloys with compositions close to the A380 alloy (A356.0 and A360.2) were used. Yield strength was considered as the main design criteria, thus the target mechanical property. Tensile testing results showed that with an optimized T6 heat treatment, not only the yield strength, but also ultimate tensile strength and elongation correspond well to the properties in the HPDC component.

sted, utgiver, år, opplag, sider
Springer, 2019. s. 435-442
Emneord [en]
Aluminium alloys, Heat treatment, Prototyping, Aluminum alloys, Die casting, Light metals, Mechanical properties, Molds, Plaster, Product design, Software prototyping, Tensile strength, Tensile testing, Yield stress, Commercial alloys, Design criteria, Design optimization, Dimension accuracy, High pressure die casting, High pressure die casts, T6 heat treatment, Ultimate tensile strength, Silicon alloys
HSV kategori
Identifikatorer
URN: urn:nbn:se:hj:diva-43728DOI: 10.1007/978-3-030-05864-7_56Scopus ID: 2-s2.0-85064856753ISBN: 9783030058630 (tryckt)ISBN: 9783030058647 (digital)OAI: oai:DiVA.org:hj-43728DiVA, id: diva2:1317196
Konferanse
Light Metals Symposium held at the TMS Annual Meeting and Exhibition, 2019, San Antonio, United States, 10 - 14 March 2019
Tilgjengelig fra: 2019-05-22 Laget: 2019-05-22 Sist oppdatert: 2019-05-22bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Bogdanoff, ToniGhassemali, EhsanRiestra, MartinSeifeddine, Salem

Søk i DiVA

Av forfatter/redaktør
Bogdanoff, ToniGhassemali, EhsanRiestra, MartinSeifeddine, Salem
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

doi
isbn
urn-nbn

Altmetric

doi
isbn
urn-nbn
Totalt: 146 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf