Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The influence of cooling rate on microstructure, tensile and fatigue behavior of heat treated Al-Si-Cu-Mg alloys
University of Bologna.
University of Bologna.
University of Bologna.
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0001-6481-5530
Visa övriga samt affilieringar
2017 (Engelska)Ingår i: Liquid metals and alloys: From structure to industrial applications / [ed] Lars Arnberg, Franco Bonollo and Roberto Montanari, Trans Tech Publications, 2017, s. 81-92Kapitel i bok, del av antologi (Refereegranskat)
Abstract [en]

Al-Si-Mg alloys are commonly employed for the production of automotive castings. In view of the recent stringent emissions standards and consequent engine downsizing, these components must withstand higher temperatures and stresses than in the past. In this regard, the heat treatable quaternary Al-Si-Cu-Mg alloys gained particular interest in recent years, due to their superior mechanical properties and higher thermal stability. The present research activity was addressed to evaluate the influence of cooling rate on microstructure and consequently on room temperature tensile and fatigue behaviour of the A354 and C355 alloys. Samples for mechanical tests were produced under controlled cooling rates, in order to induce different secondary dendrite arm spacing (SDAS) values, classified as fine (20-25μm) and coarse (50-70μm). The experimental results showed that the cooling rate strongly influences the type, size and morphology of intermetallic particles. The presence of coarse intermetallic phases, mostly Fe-based, observed in coarse SDAS specimens, was reported to strongly affect ultimate tensile strength (UTS), elongation to failure and fatigue strength of both the investigated alloys. A correlation between UTS and fatigue resistance was found, independent of microstructural coarseness.

Ort, förlag, år, upplaga, sidor
Trans Tech Publications, 2017. s. 81-92
Serie
Materials Science Forum, ISSN 0255-5476, E-ISSN 1662-9752 ; 884
Nyckelord [en]
Al-Si-Cu-Mg alloys, cooling rate, casting, microstructure, intermetallics, mechanical properties
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
URN: urn:nbn:se:hj:diva-34155DOI: 10.4028/www.scientific.net/MSF.884.81Scopus ID: 2-s2.0-85011067796ISBN: 978-3-03835-640-0 (tryckt)ISBN: 978-3-0357-0121-0 (digital)OAI: oai:DiVA.org:hj-34155DiVA, id: diva2:1051462
Forskningsfinansiär
KK-stiftelsenTillgänglig från: 2016-12-02 Skapad: 2016-12-02 Senast uppdaterad: 2018-09-19Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Seifeddine, Salem

Sök vidare i DiVA

Av författaren/redaktören
Seifeddine, Salem
Av organisationen
JTH, Material och tillverkning
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
isbn
urn-nbn

Altmetricpoäng

doi
isbn
urn-nbn
Totalt: 225 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf