Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Investigation of residual stresses generation in aluminum flywheel
Högskolan i Jönköping, Tekniska Högskolan, JTH. Forskningsområde Datorstödd konstruktion. Högskolan i Jönköping, Tekniska Högskolan, JTH, Maskinteknik. (Afsaridis Kimon)
2009 (Engelska)Självständigt arbete på avancerad nivå (masterexamen), 30 poäng / 45 hpStudentuppsats/ExamensarbeteAlternativ titel
Investigation of residual stresses by using both simulations(MAGMAsoft) and pysical measurements(Hole Drilling Method) (Engelska)
Abstract [en]

Quality of the castings is affected by several factors which the designer should take into consideration during the product development process. Although residual stress is one of those, it is often not considered in practical computations. Hence residual stresses are one of the forgotten areas in designing of machine parts. This master thesis is focused on the investigation of residual stresses in a high pressure die casted component, with the aim of extending its service life, by taking results from the study as a feedback.

The investigation of residual stresses was done on a variety of specimens, cast aluminum flywheel, provided by Husqvarna AB. This flywheel is a component in a product of the same company.In evaluating the residual stresses in the part, two tools-simulation and physical measurement were used. Moreover, comparison with these two methods is also done at an area of interest on the flywheel. The simulation was carried out by using MAGMAhpdc-a module for high pressure die casting process, from the commercial software package MAGMAsoft; while for the physical measurements, the hole drilling method was used, a method believed to be less accurate at low stresses areas.

The findings obtained from this study show that the results from both procedures are close, with small deviations observed, which reveals the reliability of the hole drilling method even when the stress levels are low. It is also found that the compressive residual stresses dominate in the component-a preferred phenomenon with regards to residual stress.

Ort, förlag, år, upplaga, sidor
2009. , s. 85
Serie
JTH Working Reports
Nyckelord [en]
High Pressure Die Casting, Residual Stresses, Hole Drilling Method, Aluminium flywheel, Compressive stresses, Tensile stresses, Distortion, Convergence, Feeding
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:hj:diva-9255OAI: oai:DiVA.org:hj-9255DiVA, id: diva2:220634
Presentation
(Engelska)
Uppsök
teknik
Handledare
Tillgänglig från: 2010-06-18 Skapad: 2009-06-01 Senast uppdaterad: 2010-06-18Bibliografiskt granskad

Open Access i DiVA

fulltext(13939 kB)9003 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 13939 kBChecksumma SHA-512
c74d503972ebfb36875e8f487ddb63d5aefb05720f425dc8f96606600bfa4302a3e8032bf124060a6779682b1d3579fb88b7d9ec1faa3dd322b0ffb3f9f22dac
Typ fulltextMimetyp application/pdf

Sök vidare i DiVA

Av författaren/redaktören
Afsaridis, Kimon
Av organisationen
JTH. Forskningsområde Datorstödd konstruktionJTH, Maskinteknik
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 9003 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 1482 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf