Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
A microstructure evaluation of different areas of resistance spot welding on ultra-high strength TRIP1100 steel
Isfahan Univ Technol, Dept Mat Engn, Esfahan, Iran.
Isfahan Univ Technol, Dept Mat Engn, Esfahan, Iran.
Isfahan Univ Technol, Dept Mat Engn, Esfahan, Iran.
Högskolan i Jönköping, Tekniska Högskolan, JTH, Material och tillverkning.ORCID-id: 0000-0002-7527-719X
Visa övriga samt affilieringar
2018 (Engelska)Ingår i: Cogent Engineering, Vol. 5, nr 1Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In this study, the microstructure of resistance spot welds of advanced ultra-high strength TRIP1100 steel was investigated. For this purpose, welding was performed after determining the best welding parameters. Four sections of the heat-affected zone (HAZ) regions were selected in the regions where the heat exchange was used to control the microstructure. Then, they were used with EBSD by scanning electron microscopy (SEM). The results showed that the TRIP1100 steel microstructure consisted of polygonal ferrites, bainites, residual austenite (RA) and martensite/austenitic islands (M/A). They also showed that the melting zone (FZ) has a lath martensite structure, and the grains are larger in packets. The structure of the martensite and different orientation grains are located in the Upper-critical area (UCHAZ). In the inter-critical region (ICHAZ), the high carbon martensitic content is higher due to the presence and the structure of ferrite and martensite. In the sub-critical region (SCHAZ), due to the tempering of martensite at a temperature below A(C1), the structure is similar to the base metal (BM), with the difference that the RA degradation reduces its structure by 50%. It was found that the RA in the BM had completely transformed. The results showed that with the movement of the BM to the weld metal, the boundaries with a low angle were increased.

Ort, förlag, år, upplaga, sidor
Cogent OA , 2018. Vol. 5, nr 1
Nyckelord [en]
resistance spot weld; TRIP1100; EBSD and microstructure
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
URN: urn:nbn:se:hj:diva-41517DOI: 10.1080/23311916.2018.1512939ISI: 000444088300001Lokalt ID: JTHMaterialISOAI: oai:DiVA.org:hj-41517DiVA, id: diva2:1250049
Tillgänglig från: 2018-09-21 Skapad: 2018-09-21 Senast uppdaterad: 2018-09-21Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Ghassemali, Ehsan

Sök vidare i DiVA

Av författaren/redaktören
Ghassemali, Ehsan
Av organisationen
JTH, Material och tillverkning
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 1654 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf