Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Microstructure formation of porous sintered Ti-Si-Zr compacts with mechanically alloyed-activated Ti-Si and TiH2 powders
Högskolan i Jönköping, Tekniska Högskolan, JTH. Forskningsmiljö Material och tillverkning – Gjutning.ORCID-id: 0000-0002-0101-0062
Nanyang Technological University, School of Mechanical and Aerospace Engineering, Singapore.
Nanyang Technological University, School of Mechanical and Aerospace Engineering, Singapore.
2014 (engelsk)Inngår i: Journal of Alloys and Compounds, ISSN 0925-8388, E-ISSN 1873-4669, Vol. 594, s. 202-210Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Metallic implants are widely used in applications associated with bone. A major drawback of using metals is their elastic modulus which is higher than that of bone resulting in stress shielding and premature failure of the implant. The employment of biomaterials with a porous structure has the potential to lower the modulus and promote osseointegration. The present work investigates the microstructure formation and the resulting elastic modulus of a new Ti-Si-Zr alloy. The sintering procedure involves the use of both mechanically alloyed Ti-Si powder and TiH2 to activate sintering with the TiH2 also serving as a pore precursor. The procedure is designed to promote bonding but not consolidation. The influence of sintering temperature, heating rate, as well as the amount and size of the TiH2 on the phases formed and porosity was investigated. It was observed that the use of TiH2 increased the degree of porosity whilst the size of TiH2 particles could be used to control the pore size. The results showed that when using small TiH2 particles, the elastic modulus was strongly dependent on the fraction of TiH2. When large TiH2 particles were used, the porosity had no significant influence on the elastic modulus. The variation in behavior could be attributed to differences in microstructure. To control the bulk modulus it is essential to understand the differences in the microstructure formation mechanisms between these two cases. (C) 2014 Elsevier B.V. All rights reserved.

sted, utgiver, år, opplag, sider
2014. Vol. 594, s. 202-210
Emneord [en]
Titanium, Zirconium, Silicon, Titanium dihydride, Transient liquid phase sintering, Mechanical alloying
HSV kategori
Identifikatorer
URN: urn:nbn:se:hj:diva-25917DOI: 10.1016/j.jallcom.2014.01.105ISI: 000331723100034Scopus ID: 2-s2.0-84894207326Lokal ID: JTHMaterialISOAI: oai:DiVA.org:hj-25917DiVA, id: diva2:789196
Tilgjengelig fra: 2015-02-18 Laget: 2015-02-18 Sist oppdatert: 2017-12-04bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Jarfors, A. E. W.

Søk i DiVA

Av forfatter/redaktør
Jarfors, A. E. W.
Av organisasjonen
I samme tidsskrift
Journal of Alloys and Compounds

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 297 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf