Ändra sökning
Länk till posten
Permanent länk

Direktlänk
BETA
Elmquist, Lennart
Publikationer (10 of 25) Visa alla publikationer
Matsushita, T., Saro, A. G., Elmquist, L. & Jarfors, A. E. .. (2018). On the thermal conductivity of CGI and SGI cast irons. International Journal of Cast Metals Research, 31(3), 135-143
Öppna denna publikation i ny flik eller fönster >>On the thermal conductivity of CGI and SGI cast irons
2018 (Engelska)Ingår i: International Journal of Cast Metals Research, ISSN 1364-0461, E-ISSN 1743-1336, Vol. 31, nr 3, s. 135-143Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The thermal conductivity of Compacted Graphite Iron (CGI) and spheroidal graphite iron (SGI) was established in the temperature range from room temperature up to 500 °C using the experimental thermal diffusivity, density and specific heat values. The influence of nodularity, graphite amount, silicon content and temperature on the thermal conductivity of fully ferritic high-silicon cast irons was investigated. It was found that the CGI materials showed higher thermal conductivity than the SGI materials. The thermal conductivity tended to increase with increasing temperature until it reached a maximum followed by a subsequent decrease as temperature was increased up to 500 °C. Conventional models were applied to estimate thermal conductivity and the predictive accuracy of each model was evaluated. The thermal conductivity could be estimated by the Helsing model. The Maxwell model, Bruggeman model and Hashin–Shtrikman model were also in fair agreement using the thermal conductivity value of graphite parallel to the basal planes in graphite. 

Ort, förlag, år, upplaga, sidor
Maney Publishing, 2018
Nyckelord
cast iron, high-silicon, modelling, Thermal conductivity, Ferritic steel, Graphite, Iron, Models, Silicon, Specific heat, Compacted graphite iron, Conventional models, Increasing temperatures, Predictive accuracy, Silicon cast iron, Silicon contents, Spheroidal graphite, Temperature range
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
urn:nbn:se:hj:diva-38338 (URN)10.1080/13640461.2017.1379263 (DOI)000437344000002 ()2-s2.0-85029576971 (Scopus ID)
Tillgänglig från: 2018-01-04 Skapad: 2018-01-04 Senast uppdaterad: 2019-02-14Bibliografiskt granskad
Ghasemi, R. & Elmquist, L. (2014). Cast iron and the self-lubricating behaviour of graphite under abrasive wear conditions. In: : . Paper presented at 10th International Symposium on the Science and Processing of Cast Iron – SPCI10.
Öppna denna publikation i ny flik eller fönster >>Cast iron and the self-lubricating behaviour of graphite under abrasive wear conditions
2014 (Engelska)Konferensbidrag, Muntlig presentation med publicerat abstract (Refereegranskat)
Abstract [en]

Cast iron is assessed as a self-lubricating material under sliding conditions. This is due to the graphite particles distributed in the matrix, which come out from their pocket, and form a tribofilm between the mating surfaces, and by which improve the tribological characteristics. In this study, the directionality and the interaction between the graphite and matrix material was investigated by microindentation and microscratch techniques. The results showed that the graphite is fractured and pushed out from the middle of graphite lamellas as a result of indentation. It was also observed that the graphite orientation below the surface intensely influenced the pushing out behaviour. For the graphite oriented toward the indenter position, the effect was more pronounced. Moreover, it was found that a scratch test can be used to investigate and explain the graphite pushing out tendency. The result was used to explain the directionality and closing tendency of the graphite lamellas during sliding.

Nyckelord
lamellar graphite iron, graphite self-lubricating behaviour, tribological performance, microindentation test, microscratch test
Nationell ämneskategori
Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Identifikatorer
urn:nbn:se:hj:diva-25199 (URN)
Konferens
10th International Symposium on the Science and Processing of Cast Iron – SPCI10
Forskningsfinansiär
EU, Europeiska forskningsrådet, 265861 (Helios)
Tillgänglig från: 2014-12-01 Skapad: 2014-12-01 Senast uppdaterad: 2018-09-11Bibliografiskt granskad
Kasvayee, K. A., Elmquist, L., Jarfors, A. E. .. & Ghassemali, E. (2014). Development of a pattern making method for strain measurement on microstructural level in ferritic cast iron. In: : . Paper presented at 23rd International Conference on Processing and Fabrication of Advanced Materials (PFAM-XXIII), Roorkee, India, December 5-7, 2014.
Öppna denna publikation i ny flik eller fönster >>Development of a pattern making method for strain measurement on microstructural level in ferritic cast iron
2014 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The current paper focuses on development of a method for studying micro-scale strains on the microstructure of ferritic cast iron. For this purpose, in-situ tensile tests were done under the optical microscope combined with digital image correlation (DIC). Critical in this development was to be able to achieve a reliable high spatial resolution of strain around microstructural features, such as graphite particles. Measurement of local strain fi elds in cast iron materials have so far been relying on displacement of naturally occurring microstructure patterns such as graphite particles, which limits the spatial resolution of strain measurement. In order to increase the spatial resolution of the measured strain, a pit etching procedure was applied to generate a random speckle pattern on the ferritic matrix. Th e critical challenges of in-situ investigation of microstructural deformation were identifi ed as speckle pattern quality and accurate selection of subset size and strain window size. Th e traceability of this method was studied by benchmarking the measured elastic modulus with that obtained from full-scale tensile test. Th e elastic modulus calculated from average strains, measured by DIC, showed a good agreement with material’s elastic modulus. Th is validates the measured localized strain values and can be used as a validation for modeling of local deformation.

Nyckelord
Ferritic cast iron, Digital image correlation (DIC), In-situ tensile test, Pit etching, Subset size, Strain window size
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
urn:nbn:se:hj:diva-28326 (URN)
Konferens
23rd International Conference on Processing and Fabrication of Advanced Materials (PFAM-XXIII), Roorkee, India, December 5-7, 2014
Tillgänglig från: 2015-11-16 Skapad: 2015-11-16 Senast uppdaterad: 2017-08-14Bibliografiskt granskad
Ghasemi, R., Elmquist, L., Svensson, H., König, M. & E. W. Jarfors, A. (2014). Mechanical properties of solid solution strengthened CGI. In: : . Paper presented at 10th International Symposium on the Science and Processing of Cast Iron – SPCI10.
Öppna denna publikation i ny flik eller fönster >>Mechanical properties of solid solution strengthened CGI
Visa övriga...
2014 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The development of high-performing components is crucial in applications such as heavy vehicleautomotive powertrains. In these applications, strength, weight and thermal conductivity isessential properties. Key materials that may fulfil these requirements include cast irons of differentgrades where in terms of manufacturability and in particular, machinability pearlitic grades aredifficult due to hardness variation, where a fully ferritic matrix would provide an advantage. Toachieve maximum strength a fully ferritic and solid solution strengthened compacted graphite iron(CGI) would provide an interesting alternative to the automotive industry. In the current study, theeffect of Si level on mechanical properties in a fully ferritic material was investigated. The influenceof section thickness on tensile properties and hardness was investigated. The resulting materialwas fully ferritic with limited pearlite content. Section thickness influence on nodularity and hencethe mechanical properties were also investigated.

Nyckelord
compacted graphite iron, high Si ferritic CGI, mechanical properties, solution hardening, ferrite
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
urn:nbn:se:hj:diva-25198 (URN)
Konferens
10th International Symposium on the Science and Processing of Cast Iron – SPCI10
Forskningsfinansiär
Vinnova, DNR 2012_137 2.4.2
Tillgänglig från: 2014-12-01 Skapad: 2014-12-01 Senast uppdaterad: 2014-12-09Bibliografiskt granskad
Ghasemi, R. & Elmquist, L. (2014). The relationship between flake graphite orientation, smearing effect, and closing tendency under abrasive wear conditions. Wear, 317(1–2), 153-162
Öppna denna publikation i ny flik eller fönster >>The relationship between flake graphite orientation, smearing effect, and closing tendency under abrasive wear conditions
2014 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 317, nr 1–2, s. 153-162Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Abstract Plastic deformation of the matrix during the wear process results in closing the graphite flakes. In this study, the relationship between the deformation of the matrix and the closing tendency of flake graphite was investigated, both qualitatively and quantitatively. Two representative piston rings, which belonged to the same two-stroke marine engine but were operated for different periods of time, were studied. Initial microstructural observations indicated a uniform distribution of graphite flakes on unworn surfaces, whereas worn surfaces demonstrated a tendency towards a preferred orientation. Approximately 40% of the open flakes of the unworn surfaces were closed during sliding, which may result in the deterioration of the self-lubricating capability of cast iron. Moreover, flakes within the orientation range of 0 to 30° relative to the sliding direction showed a maximum closing tendency when subjected to sliding. The closing tendency gradually decreased as the angle increased, approaching a minimum between 30 and 70°. A slight increase in the closing tendency was observed for flakes with orientations between 70 and 90°. A similar trend was observed on both rings. Furthermore, SEM and EDS analysis indicated substantial deformation of the matrix in the area around the flakes. An insignificant corrosion attack was observed on both worn piston ring surfaces.

Nyckelord
Grey cast iron, Piston ring-cylinder liner, Flake graphite orientation, Sliding wear, Abrasive wear, Graphite closing tendency
Nationell ämneskategori
Metallurgi och metalliska material Bearbetnings-, yt- och fogningsteknik
Identifikatorer
urn:nbn:se:hj:diva-24210 (URN)10.1016/j.wear.2014.05.015 (DOI)000341340700015 ()2-s2.0-84902973160 (Scopus ID)
Projekt
European project entitled Helios
Forskningsfinansiär
EU, FP7, Sjunde ramprogrammet, 265861
Tillgänglig från: 2014-07-07 Skapad: 2014-07-03 Senast uppdaterad: 2017-12-05Bibliografiskt granskad
Elmquist, L., Eriksson, L. & Ekman, F. (2014). Workshop at a company with students from two different disciplines. In: : . Paper presented at 10th International CDIO Conference 16-19 June, Barcelona, Spain.
Öppna denna publikation i ny flik eller fönster >>Workshop at a company with students from two different disciplines
2014 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Teachers from two different disciplines, Materials and manufacturing and Industrial design, are brought together to give a course on masters level. Also the students come from different disciplines. They study two different master programs in Product development, Product development and materials engineering and Industrial design. The course is called Materials and design, and it covers both disciplines. Apart from lectures, computer labs and home assignments, a workshop was arranged where the students during one day solved a task related to product development. The students were divided into groups in such a way that a mixture of students from the two programs was obtained. The workshop was held at a company in order to make the work more realistic. Before they started to solve the task, they were given an introduction to the products made by the company and their applications. The main task was then to investigate the products and come up with ideas about what applications there might be in the future. The result was at the end of the day presented to the company. In this paper, the workshop is described, and comments and reflections from the students and the company are summarized. Finally the teachers involved give their opinion about the result and the pedagogic benefits from such a workshop, and also what to think about for the next time. It appeared that the workshop was an eye-opener to the company at the same time as the students had a fair chance to work in a realistic situation and practice how to use their knowledge. Also for the teachers it was a good experience, not only from a pedagogic viewpoint but also on how to arrange this kind of workshops in the future.

Nyckelord
Problem-based learning, reflective learning, industrial relevance, T-shaped engineering, CDIO Standards
Nationell ämneskategori
Annan teknik
Identifikatorer
urn:nbn:se:hj:diva-24189 (URN)
Konferens
10th International CDIO Conference 16-19 June, Barcelona, Spain
Tillgänglig från: 2014-07-01 Skapad: 2014-07-01 Senast uppdaterad: 2017-10-26Bibliografiskt granskad
Soivio, K. & Elmquist, L. (2013). Influence of inoculation on shrinkage defects in spheroidal graphite cast iron. International Journal of Cast Metals Research, 26(4), 220-227
Öppna denna publikation i ny flik eller fönster >>Influence of inoculation on shrinkage defects in spheroidal graphite cast iron
2013 (Engelska)Ingår i: International Journal of Cast Metals Research, ISSN 1364-0461, E-ISSN 1743-1336, Vol. 26, nr 4, s. 220-227Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Defective castings produce unnecessary costs for foundries. Common flaw in spheroidal graphite cast iron castings are shrinkage defects. In literature it is suggested that by controlling the graphite precipitation it is possible to suppress the shrinkage propensity of the melt. The most influential way of effecting the graphite precipitation is inoculation. In this work the effectiveness of different commercial inoculant products and inoculation methods in reducing the shrinkage defects on cast component were researched. Significant difference in performance was observed between ladle and stream inoculation methods in preference of stream inoculation. Differences were also seen between different inoculants and how they behaved in combinations when ladle and stream inoculants were added simultaneously. It was observed that not all of the combinations were beneficial. In order to decrease the cost caused by shrinkage defects a proper selection of inoculation method and inoculant is of importance.

Ort, förlag, år, upplaga, sidor
Maney Publishing, 2013
Nyckelord
spheroidal graphite cast iron, shrinkage defects, microshrinkage, graphite, inoculation
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
urn:nbn:se:hj:diva-20854 (URN)10.1179/1743133613Y.0000000057 (DOI)000322819600005 ()2-s2.0-84881077327 (Scopus ID)
Projekt
YMPA - Kvalitetsstyrning vid tillverkning av gjutjärnskomponenter
Forskningsfinansiär
KK-stiftelsen, 20080660
Tillgänglig från: 2013-03-18 Skapad: 2013-03-18 Senast uppdaterad: 2018-10-15Bibliografiskt granskad
Eckert, G., Hjelmåker, M. & Elmquist, L. (2013). Off campus integrating theory and practice with progression. In: : . Paper presented at 9th International CDIO Conference 9-13 June, Cambridge USA.
Öppna denna publikation i ny flik eller fönster >>Off campus integrating theory and practice with progression
2013 (Engelska)Konferensbidrag, Enbart muntlig presentation (Övrigt vetenskapligt)
Nationell ämneskategori
Teknik och teknologier
Identifikatorer
urn:nbn:se:hj:diva-21532 (URN)
Konferens
9th International CDIO Conference 9-13 June, Cambridge USA
Tillgänglig från: 2013-06-20 Skapad: 2013-06-20 Senast uppdaterad: 2013-07-10Bibliografiskt granskad
Svensson, I. L., Seifeddine, S., Elmquist, L., Sjölander, E. & Sjögren, T. (2012). On characterization and modeling of mechanical properties of materials for cast components. In: : . Paper presented at WFC 2012, World Foundry Congress, Monterrey, Mexico, 24-27 April, 2012.
Öppna denna publikation i ny flik eller fönster >>On characterization and modeling of mechanical properties of materials for cast components
Visa övriga...
2012 (Engelska)Konferensbidrag, Enbart muntlig presentation (Refereegranskat)
Nationell ämneskategori
Metallurgi och metalliska material
Identifikatorer
urn:nbn:se:hj:diva-19886 (URN)
Konferens
WFC 2012, World Foundry Congress, Monterrey, Mexico, 24-27 April, 2012
Tillgänglig från: 2012-11-27 Skapad: 2012-11-27 Senast uppdaterad: 2017-08-14Bibliografiskt granskad
Elmquist, L. & Sonawane, P. (2012). On the relation between primary and eutectic solidification structures in gray iron. In: : . Paper presented at The 3rd International Conference on Advances in Solidification Processes, 7–10 June 2011, Rolduc Abbey, Aachen, The Netherlands. Institute of Physics (IOP), 27(1)
Öppna denna publikation i ny flik eller fönster >>On the relation between primary and eutectic solidification structures in gray iron
2012 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The solidification of hypoeutectic gray cast iron starts with the nucleation of primary austenite crystals. Before graphite is nucleated, and the eutectic structure is formed, these crystals start to grow as columnar or equiaxed dendrites. However, very little is known about these dendrites, and especially how they influence the subsequent eutectic structure. Besides, it has previously been shown that the primary solidification structure influences the formation of defects. Shrinkage porosity was found between the dendrites, in the grain boundaries, and the formation of the primary solidification structure was found to influence problems related to metal expansion penetration. Therefore a better understanding about the formation of this structure is of importance. In this work, different inoculants and their influence on the formation of the micro- and macrostructures has been investigated. The inoculants considered are commercially used inoculants, i.e. inoculants used in the foundries, as well as different iron powders. The addition of iron powder is used to promote the primary solidification structure. It is shown that the nucleation of the dendrites is influenced by the amount of iron powder. Secondary dendrite arm spacing is a quantitative measurement in the microstructure related to these dendrites, which in turn depends on the solidification time. Eutectic cell size, on the other hand, is found to depend on secondary dendrite arm spacing. It is shown how the addition of inoculants influences both primary and eutectic solidification structures, and how they are related to each other.

Ort, förlag, år, upplaga, sidor
Institute of Physics (IOP), 2012
Serie
IOP Conference Series: Materials Science and Engineering, ISSN 1757-8981, E-ISSN 1757-899X ; 27
Nationell ämneskategori
Materialteknik
Identifikatorer
urn:nbn:se:hj:diva-23077 (URN)10.1088/1757-899X/27/1/012060 (DOI)000301192900060 ()
Konferens
The 3rd International Conference on Advances in Solidification Processes, 7–10 June 2011, Rolduc Abbey, Aachen, The Netherlands
Tillgänglig från: 2014-01-13 Skapad: 2014-01-13 Senast uppdaterad: 2018-09-14Bibliografiskt granskad
Organisationer

Sök vidare i DiVA

Visa alla publikationer